FLYGT 3152 PDF

2. C C Product. Submersible pump for pumping clean water, surface water and waste water containing solids or long-fibred material. Denomination. Dataplate. rpm. Max 40°C. YSER/Y//V. 26/51A. kWhp. Date: Flygt CS MT. Use our handy online form to submit details on your existing Flygt pump to get a Flygt C Submersible Pumps Range Flygt C LT Submersible.

Author: Brashakar Mezuru
Country: Cambodia
Language: English (Spanish)
Genre: Career
Published (Last): 2 April 2012
Pages: 215
PDF File Size: 8.30 Mb
ePub File Size: 18.88 Mb
ISBN: 994-3-86127-285-1
Downloads: 99606
Price: Free* [*Free Regsitration Required]
Uploader: Malashura

Before operating the unit after storage: Seek medical attention, if required. Before assembling the pump housing and the drive unit end, check the following: Place the pump on the base and make sure it cannot fall over or sink. The drive unit is not receiving full voltage on all three phases. Alternatively, the fljgt can be suspended with a lifting chain just above the sump bottom.

LL Replace the wear ring in the pump housing, diffuser ring, or suction cover Figure The pipes and joints leak. Remove the impeller, impeller hub, or propeller using a impeller hub.

Flygt 3000 Series / C Submersible Pumps

If necessary, saw grooves in the wear ring using a hacksaw. Contact an Xylem service shop. Remove the impeller screw and washer. Check the contactor and the control circuit.

TOP Related Posts  ACUSOLVE TUTORIALS PDF

Check that the impeller rotates according to this illustration. Unscrew the four cap nuts and withdraw the lower wear protection from the pump housing.

Product specifications | Flygt 3152 – Alaska Pump and Supply

Rotation direction Check the impeller rotation. Do NOT use the pump in highly corrosive liquids. The earth ground lead must be 50 mm 2. For the pump to perform at maximum capacity, the impeller must be adjusted regularly. Tighten the lock nuts evenly all around. Before assembling the pump housing or diffuser ring with the drive unit end, check the following: Within the first year of operation. Tightening torque, see Torque values page 32 4.

We move, treat, analyze, and return water to the environment, and we help people use water efficiently, in their homes, buildings, factories and farms. Fit and tighten the cap nuts. Drive in the new wear ring. Observe these guidelines and warnings for electrical connections: Oversized lifting equipment could cause damage if the unit should stick when being lifted.

Find the leaks and seal them. This is an example of a sales denomination, and an explanation of its parts. Dry running during service and inspection is only permitted outside the classified area.

Place the pump in a horizontal position. There is a malfunction in the overload protection. O-ring Wear ring in the pump casing Impeller wear ring Figure The phase currents vary, or they are too high. For more information contact your Xylem representative.

TOP Related Posts  AGENDA BUTXACA PDF

Mechanical seal Replace with new seal units. Product and product positioning requirements Observe these requirements for the product and the product positioning: Lay the drive unit on its side. Remove the upper wear protection.

Flygt Series / C Submersible Pumps

Clean or replace if necessary. Adjust the suction cover: Cause Remedy The pump is unable to empty the sump to the stop level. The pipes are obstructed. Do NOT override the motor protection repeatedly flhgt it has tripped.

Check the condition of the lifting handle. F Required tools for F Back off the sleeve screws a quarter turn.

The data plate The data plate is a metal label located on the main body of the pump. Contact the local Xylem service shop. Clean the level regulators. Earthing grounding Observe the following regulations for earthing grounding connections.

The overload protection Check that the impeller can rotate freely. Check that the impeller can rotate freely. Install the access frame: The CLS sensor body is made of glass.