HT12D is a series decoder IC for remote control applications manufactured by Holtek. It is commonly used for radio frequency (RF) applications. Download. HT12D. 8. 4. L. Ö. RC oscillator. DIN active ²Hi². 18DIP, 20SOP. HT12F. 0 Holtek¢s series of encoders (refer to the encoder/de- . C o n tro l L o g ic The information appearing in this Data Sheet is believed to be accurate at the . HT12DDIP Ic-remote Control Decoder Features. Operating voltage: V~12V Low power and high noise immunity CMOS technology Low standby current.

Author: Meztirisar Kazirisar
Country: Seychelles
Language: English (Spanish)
Genre: Love
Published (Last): 11 October 2017
Pages: 107
PDF File Size: 15.90 Mb
ePub File Size: 2.45 Mb
ISBN: 759-6-19806-775-5
Downloads: 32479
Price: Free* [*Free Regsitration Required]
Uploader: Gardagal

The Encoded 12 bit output data obtained from HT12E has to be given here. This pin will go high when a data is received. For decoding a data the IC will requires an oscillatorluckily this IC has one in-built. The input data code is decoded when no error or unmatched codes are found.

The serial input data is compared with the local addresses three times continuously. So if you are working on a project which has to transmit a 4-bit data from one end to other xecoder by wire or wireless then this IC pair will be best suited for you.

Customers who bought this product also purchased Choosing Motor For Robots. They are capable of Encoding 12 bit of information which consists of N address bits and N data bits. The IC has a built datashet oscillator.

This high-density System-in-Package SiP integrates controller, power switches, and support components. The IC is should be powered by 5V pin 18 and the ground pin pin 9 is grounded.

TOP Related Posts  BOBRICK B-2112 PDF

This pin powers the IC should use only 5V.

If you want security you can connect any of the 8 pins to 5V to make it high. Choosing Battery for Robots. In simple terms, Decoderr converts the serial input into parallel outputs. Arduino based GPS receiver. So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data. These two ICs together form an Daatasheet and Decoder pair. A valid transmission in indicated by a high signal at VT pin. Buy 15 or more pieces to get Free Shipping Option Availability: This oscillator can be used by connecting these two pins through a 1M Resistor.

To know how a 4-bit data can be encoded and then send to the input pin of this IC, we have to understand the working of the HT12E Encoder IC which is given here.


HT12D/HT12F – Product Details – Holtek

Valid transmission; active high. Interface GPS with Arduino. The 4-bit data that is received can be obtained on pins AD0 to AD1 and an address of 8-bit has to be set using the pins A0 to A7.

Skip to main content. The Decoder receive the serial address and data from its corresponding decoder, transmitted by a carrier using an Darasheet transmission medium and gives output to the output pins after processing the data. What is Web Browser. This series of decoders are mainly used for remote control system applications, like burglar alarm, car door controller, security system etc.

Interface SD Card with Arduino. We will notify you the result by email. In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground.


HT12D is a decoder integrated circuit that belongs to 2 12 series of decoders. Thanks a lot for helping us to maintain competitive prices.

HT12D Decoder IC

TB Stepper Motor Driver 4. Mercury ball tilt switch 5mm dia. Return and Refund Policy. Connected to the Ground of circuit. Please submit the url of the better price you saw.

The data on 4 bit latch type output pins remain unchanged until new is received. Actual h12d may vary from the product photograph displayed above. It decodes the serial addresses and data received by, say, an RF receiver, into parallel data and sends them to output data pins.

Virgin Galactic — Commercial Space Flight. Found this item with same quality and at a lower price but devoder to buy from robokits. Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc.

This oscillator can be used by connecting these two pins through a 1M Resistor 17 Valid Transmission VT This pin will go high when a data is received. Easy Interface with and RF or an Infrared transmission medium. Be the first to write a review. This ICs are paired with each other.